Quizzes & Puzzles0 min ago
Help Please - Motorbike Battery.
I am a total moron when it comes to anything mechanical....
I took the battery out of my bike a while ago. I should have taken a photo so that I knew how to reinstall it (stupid mistake).
I have just gone to reinstall it and there are two black leads which go onto the negative terminal and a red one to go on the positive. So far so good - even I know that much.
The problem is there's two additional, smaller leads, one black one and one with a red sheath, and for the life of me I don't remember removing them. The obvious answer (it seems to me) is to put the black one on the negative terminal with the two main black leads and the red one on the positive terminal with the main positive lead. However, they're tied fairly close together, and whilst both will go on either the negative or the positive, there's not enough for one to go on each, which leads me to the conclusion they must both go on to just one of the terminals.
I've taken a picture, but don't know how to add photos to AB.
Any help would be most appreciated.
Many thanks.
I took the battery out of my bike a while ago. I should have taken a photo so that I knew how to reinstall it (stupid mistake).
I have just gone to reinstall it and there are two black leads which go onto the negative terminal and a red one to go on the positive. So far so good - even I know that much.
The problem is there's two additional, smaller leads, one black one and one with a red sheath, and for the life of me I don't remember removing them. The obvious answer (it seems to me) is to put the black one on the negative terminal with the two main black leads and the red one on the positive terminal with the main positive lead. However, they're tied fairly close together, and whilst both will go on either the negative or the positive, there's not enough for one to go on each, which leads me to the conclusion they must both go on to just one of the terminals.
I've taken a picture, but don't know how to add photos to AB.
Any help would be most appreciated.
Many thanks.
Answers
Best Answer
No best answer has yet been selected by Deskdiary. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.I can't help with the electrical bit but here's how to show us a picture:
Go here: http:// upl.co/
Click the green button.
Navigate to the location of your image file and double-click on it.
When you see a thumbnail of your image, click on it to make it bigger.
Then click on that bigger pic to end up with an even bigger picture, filling the screen.
Copy the URL of that page and paste it into a reply on this thread.
Go here: http://
Click the green button.
Navigate to the location of your image file and double-click on it.
When you see a thumbnail of your image, click on it to make it bigger.
Then click on that bigger pic to end up with an even bigger picture, filling the screen.
Copy the URL of that page and paste it into a reply on this thread.
Thanks Buenchico - very helpful.
http:// upl.co/ upload/ o7Kh5Hi 5X
Hopefully the picture shows my issue.
http://
Hopefully the picture shows my issue.
Indeed, the correct orientation is the battery name and info uppermost (Yuasa YTZ10S etc.), terminals on the left side of frame, positive to rear.
http:// upl.co/ uploads /mvagus ta15240 09620.j pg
http://
From the service manual.
"WARNING: The inversion of the battery
wires can damage the battery and the
recharging system. The red wires must
be connected to the positive terminal
(+), while the black wires must be con-
nected to the negative terminal (-).
When removing the battery, disconnect
the negative terminal FIRST and then
the positive terminal. When reinstalling
the battery, use the reverse procedure." Page 169.
https:/ /www.ma nualsli b.com/m anual/8 37356/M v-Agust a-Bruta le-R.ht ml?page =169#ma nual
"WARNING: The inversion of the battery
wires can damage the battery and the
recharging system. The red wires must
be connected to the positive terminal
(+), while the black wires must be con-
nected to the negative terminal (-).
When removing the battery, disconnect
the negative terminal FIRST and then
the positive terminal. When reinstalling
the battery, use the reverse procedure." Page 169.
https:/
Related Questions
Sorry, we can't find any related questions. Try using the search bar at the top of the page to search for some keywords, or choose a topic and submit your own question.