Quizzes & Puzzles7 mins ago
Window Leaking
Landing window on gable end wall leaks in at top seems only when we get wind and rain together had gable end pointed and water sealed still rains in above window
Answers
Best Answer
No best answer has yet been selected by col72. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
Most likely a cavity wall then, Col? With a cavity, pointing would not normally cause this.
I assume the replacement uPVC windows have had a good silicone seal put around them (exterior).
Does the water appear as drips on the head over the window? (Flat bit of masonry/plaster over the top of the window.)
I assume the replacement uPVC windows have had a good silicone seal put around them (exterior).
Does the water appear as drips on the head over the window? (Flat bit of masonry/plaster over the top of the window.)
Ok.
Most likely cause in a house of this period............
With a cavity wall .......... the outer "skin" is designed to saturate. It soon evaporates. The cavity prevents direct passage of water to the inner leaf (skin.)
Putting a window/door/opening across the cavity bridges it (quite normal.)
Water in the outer leaf will trickle down onto the top of the window .... hence ......... a leak.
To prevent this, a "cavity tray" is fitted across the window. This is stepped. The inner edge of the tray is built into the inner leaf roughly 9" above the window.
The outer edge of the tray sits directly over the window (more or less.) So the tray is stepped to make the aforementioned drips run downhill ... over the window ... and safely away to outside.
In those days, the tray would be made of tar-impregnated felt (like an old-fashioned damp-course.) This rots. 60 years would be enough time for this.
A nice, thick lead one would have been better.
You with me so far?
Most likely cause in a house of this period............
With a cavity wall .......... the outer "skin" is designed to saturate. It soon evaporates. The cavity prevents direct passage of water to the inner leaf (skin.)
Putting a window/door/opening across the cavity bridges it (quite normal.)
Water in the outer leaf will trickle down onto the top of the window .... hence ......... a leak.
To prevent this, a "cavity tray" is fitted across the window. This is stepped. The inner edge of the tray is built into the inner leaf roughly 9" above the window.
The outer edge of the tray sits directly over the window (more or less.) So the tray is stepped to make the aforementioned drips run downhill ... over the window ... and safely away to outside.
In those days, the tray would be made of tar-impregnated felt (like an old-fashioned damp-course.) This rots. 60 years would be enough time for this.
A nice, thick lead one would have been better.
You with me so far?
No need for lead these days, Col. Modern heavy duty damp-course material is fine, and much easier to use.
To do this properly, the soldier arch would be taken out, plus a few bricks 6" (150mm) or so to each side.
The tray would be fixed to the inner leaf about 9" (225mm) above the window.). This would be less disruptive to the interior plaster/decorating etc.
Replace the brickwork, and you're done.
Togo. Yes, that may well be another thing, but a properly fitted tray would take care of that.
To do this properly, the soldier arch would be taken out, plus a few bricks 6" (150mm) or so to each side.
The tray would be fixed to the inner leaf about 9" (225mm) above the window.). This would be less disruptive to the interior plaster/decorating etc.
Replace the brickwork, and you're done.
Togo. Yes, that may well be another thing, but a properly fitted tray would take care of that.
if that is the case, fitting one of these would look better........
http://
http://
http://
There is a picture of a set of headers removed and a cavity tray being installed attached with this col. Not really a diy job. Unless you are proper handy.
There is a picture of a set of headers removed and a cavity tray being installed attached with this col. Not really a diy job. Unless you are proper handy.
Togo's got it, Col. That's a good pic.
Not a difficult job at all, but not for the faint-hearted. I've made a few assumptions, so it really needs to be looked at professionally, and quoted for.
A confident DIYer could easily undertake this, but it does need an experienced eye to assess any possible difficulties that might be met. I don't envisage any... but every case is slightly different.
Not a difficult job at all, but not for the faint-hearted. I've made a few assumptions, so it really needs to be looked at professionally, and quoted for.
A confident DIYer could easily undertake this, but it does need an experienced eye to assess any possible difficulties that might be met. I don't envisage any... but every case is slightly different.
