ChatterBank0 min ago
Dishwasher fault
3 Answers
Our 8yr old Whirlpool dishwasher has developed a fault.
When the machine is started it runs fine for a minute or two until I think it tries to empty the sump. The pump starts and then immediately stops after pumping a cupful or two down the drain and then repeats this until the sump is empty and then carries on as normal until later on in the sequence it does the same thing when pumping water down the drain.
We have tried various cleaning solutions to rid the sump (not that we can see it) of any gunk.
Need to know how to fix this?
The model number is ADP 4501.
When the machine is started it runs fine for a minute or two until I think it tries to empty the sump. The pump starts and then immediately stops after pumping a cupful or two down the drain and then repeats this until the sump is empty and then carries on as normal until later on in the sequence it does the same thing when pumping water down the drain.
We have tried various cleaning solutions to rid the sump (not that we can see it) of any gunk.
Need to know how to fix this?
The model number is ADP 4501.
Answers
1 to 3 of 3
Best Answer
No best answer has yet been selected by woodchopper. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
I had exactly the same problem about three months ago.... we had a smeg dishwasher, but it was doing exactly the same as yours. Everything worked only it kept emptying itself, which in turn rendered it useless.
In our case I did eventually find the fault, but it was too late as I had already started to break it up to sell on eBay for spares.
On a dishwasher you have a sump/base plate..... Floating in the sump you have a switch which is called the anti flood switch. It is basically a micro switch operated by polystyrene floats that rise when any small amount of water leaks from within the dishwasher and ends up in the sump. The switch operates the empty motor, and at the same time ends the rinse cycle.
So start by checking the sump for any sign of a leak, it only takes a up full of water to stop the cycle. The good news is your switch is working, otherwise your kitchen would be flooded.
When I broke my machine up I eventually found a tiny trace of scale which was the tell tale sign of a leak. It was totaly impossible to locate when the machine was running, but once I was removing the the components it was spotted....
The remedy would have been to tighten the screws that secure the sump from inside the washer . The ones which surround the filter plate. Or even replacing the sump gasket would propably have done it.
I collected over £100 for the parts on eBay.
When I
In our case I did eventually find the fault, but it was too late as I had already started to break it up to sell on eBay for spares.
On a dishwasher you have a sump/base plate..... Floating in the sump you have a switch which is called the anti flood switch. It is basically a micro switch operated by polystyrene floats that rise when any small amount of water leaks from within the dishwasher and ends up in the sump. The switch operates the empty motor, and at the same time ends the rinse cycle.
So start by checking the sump for any sign of a leak, it only takes a up full of water to stop the cycle. The good news is your switch is working, otherwise your kitchen would be flooded.
When I broke my machine up I eventually found a tiny trace of scale which was the tell tale sign of a leak. It was totaly impossible to locate when the machine was running, but once I was removing the the components it was spotted....
The remedy would have been to tighten the screws that secure the sump from inside the washer . The ones which surround the filter plate. Or even replacing the sump gasket would propably have done it.
I collected over £100 for the parts on eBay.
When I
1 to 3 of 3
Latest Posts
News4 mins ago
Body & Soul4 mins ago
Mountains Of The United Kingdom
Quizzes & Puzzles15 mins ago
